- Bostik Blu-Tack Reusable Adhesive
Bostik Blu-Tack is the is the original reusable adhesive. It is permanently plastic and pliable (it can be readily formed into any shape) and each pack comes with strips for ease of use. In the blue-only pack there are 4 strips each approximately 3/4 inch wide x 8 inches long and in the color pack there are 5 strips each approximately 1/2 inch wide x 8 inches long. A few applications for the putty include using to stick posters, sealing around windows and doors, cleaning dust and hair from clothing, keeping pictures straight and modeling. Use Blue-Tack on non-porous surfaces, painted surfaces, vinyl coated wall paper, glass, metal, etc. Remember to press it on, but roll it off. Any remaining Blu-Tack material can be removed by rolling or dabbing with another blob of Blue Tack. The uses are endless, but here are some others: Leave note on door. Create 3 dimensional models. Hold candles in place in holders. Remove dust from awkward places. Pick up dropped screws or nails. Attach screw to screwdriver to get to hard places. Hold figurines in place on the window sill. Use to reduce noise vibration. Hold markers in place on white board. Clean computer keys. Hold speakers in place on speaker stands. Graphite artists can use as a graphite eraser or magnet. Keep picture frames from shifting around on wall. Hold end of measuring tape on wall when measuring long runs.
- 3M Scotch 4298 Adhesion Promoter (Sponge Applicator Packet)
3M 4298 Adhesion Promoter is a liquid primer used for most low surfaces energy plastics. This would include common low surface energy plastics used for automotive dash and interior trim applications (TPO, PPO, PP, PC, PC and ABS, etc.). It is specifically formulated to be used with 3M Acrylic Foam Tapes. Since formulations and surface energies can vary for these types of materials, each application should be verified through testing. This adhesion promoter is supplied in an easy-to-use sponge applicator packet. 3M 4298 Application Procedure: the liquid contents of the packet should be completely used as soon as possible after opening. Hold packet upright and avoid squeezing an opened packet to prevent spillage of liquid contents. The packet can be opened by tearing across the top of the packet at the notches. This will expose the sponge applicator. Do not remove the sponge or squeeze a freshly opened packet. Handling the bottom section of the packet should enable application of 3M adhesion promoter 4298 with no mess. Apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. A wet coating thickness of 0.002 inch or less is recommended. Apply promoter only to areas that will be fully covered with tape. Although drying times may vary due to temperature and/or humidity, a drying time of 30 to 90 seconds is typically indicative of this thickness. The primer should be dry before applying tape. For best results, apply tape immediately after primer application or no more than one hour afterwards. Be sure the primed surface remains free from contaminants prior to tape application.
- Nashua 357SA Spray Adhesive
Nashua 357SA Spray Adhesive is designed for temporary and permanent bonding. Used to bond fabric, fiberglass insulation, plastic films, felt, rubber, leather, cork, paper, cardboard, urethane foam, foil to metal, wood to wood and a variety of other substrates. Low VOC (Volatile Organic Compounds) content and can contribute toward satisfying EQ Credit 4.1 under LEED and meets SCAQMD Rule 1168 and Green Seal GS-36 requirements. Nashua 357 Spray Adhesive features/benefits include: Fast skin, fast grab, low soak in spray adhesive. Formulated to bond polyethylene to concrete block, wood and many other hard-to-bond pieces. May be used to bond carpet and is ideal for label applications. May be used for either permanent or temporary bonds. Good UV, moisture, and oxidation resistance. It has a lace spray pattern, solvent odor, 15 second to several hour bonding time, 1 year shelf life, and its volume is 19.6 fluid ounces (net weight is 14 ounces), contains no methylene chloride, and is extremely flammable. For permanent bonds spray both surfaces; allow 1-2 minutes for tack to develop and then bond with firm pressure. For temporary bonds, apply a light, even coat to one surface; allow tack to develop and then bond with firm pressure.
- 3M Scotch 08987 General Purpose Adhesive Cleaner
3M 08987 Adhesive Cleaner is a specially blended solvent in aerosol form used for removal of light paint overspray, adhesive residue, wax, grease, tree sap, dirt, road tar, oil and bugs. Will not harm most thoroughly cured automotive paint, vinyls, or fabrics when properly used. Part number 08987 Aerosol has a VOC content of 738 grams per liter (6.16 lbs per gallon).
- 3M Scotch Series 20 Aerosol Spray Adhesives
3M Series 20 Aerosol Spray Adhesives are designed for industrial applications where keeping component costs down is key to the competitiveness of your product lines. They're ideal for a wide range of woodworking, manufacturing and construction applications. Series 20 spray adhesives have low soak-in formulas with great heat resistance. All products meet CARB/OTC VOC requirements. 3M Woodworking 20 Spray Adhesive is a high strength, fast grabbing, industrial grade, lace spray aerosol adhesive. Its used for woodworking, furniture, building, construction, transportation and marine applications. 3M Foam & Fabric 24 Spray Adhesive is a fast-tack industrial grade spray adhesive. Its used for furniture, upholstery, marine, automotive, seat and chair manufacturing, acoustics and bedding applications. 3M Multi-Purpose 27 Spray Adhesive is a versatile economical, industrial grade, mist spray aerosol adhesive. Used for general industrial lightweight applications.
- MACtac UGlu Professional Adhesive Tape
MACtac UGlu Professional Adhesive Tape is a double-sided adhesive transfer tape which combines the strength of adhesive with the convenience and ease of tape. UGlu bonds even rough and uneven surfaces instantly, without the wait, mess or hassle of liquid glue. Use for craft and kid projects, house repair and other outdoor jobs. Other features of UGlu include: Can be cut to size (clean scissors with baby or vegetable oil prior to cutting). Waterproof & weatherproof. Holds up to 2 pounds. Instant bond & permanent hold. Easy-to-peel oversized liner (the liner on the tape is extended so there is a 1/4 inch dry ungummed edge at both sides of the tape so the 1 inch tape will actually come as 1-1/2 inches since there is a 1/4 inch dry edge at both the top and the bottom). Non-toxic & acid free. Made in the USA. UGlu Professional bonds to carpet, canvas, fabrics, plastics, laminates, metal, glass, paper, wood, fiberglass, tile, granite, cement, ceiling tile, craft-foam, ceramics, drywall, foam board, etc. It should not be used on any type of wallpaper covered surfaces. To remove UGlu roll a corner of the adhesive until you have enough to grab and hold. Then pull SLOWLY away from the adhesive strip, do not pull directly up or across the surface of the remaining adhesive. If you pull too quickly the UGlu may break or snap-off. Please note removable tape is designed to not leave adhesive residue behind; however it may still pull up loose debris, finish, etc. from a substrate it is applied to depending on many conditions such as length of time applied, chemicals used to clean the substrate, and the composition of the substrate itself. We always recommend testing first on an inconspicuous area to ensure it removes as desired.
- Duck Brand Adhesive Remover Applicator & Scraper
Duck Brand Adhesive Remover removes adhesive residue, tar, caulk, gum, crayon and more. One-step, no-mess bottle applicator with a built-in sponge and scraper. The remover works on many surfaces including windows, walls, floors, furniture, glass, carpet, metal and plastic (it is always recommended to test on an inconspicuous part of the surface first). Removes adhesive residue left behind by duct tape, masking tape, carpet tape, mounting tape, weather striping tape, stickers and labels. Has a fresh citrus scent. Duck Brand Adhesive Remover Usage Instructions: Use sponge applicator to apply remover. Place scraper cap back onto bottle. Let liquid sit for 20 to 30 seconds. Remove residue using the scraper. Wipe off excess liquid. Clean surface with soap and water.
- 3M Scotch EC100 Rite-Lok Instant Adhesive Glue
3M EC100 Rite-Lok Instant Adhesive Glue is a low-medium viscosity cyanoacrylate adhesive that is fast curing and useful for general purpose bonding. It is a single component, high strength ethyl cyanoacrylate liquid adhesive which is designed to bond to a variety of substances including most plastics, rubbers, metals, and other common substrates. Some tips for applying 3M EC100: Ensure parts are clean, dry, and free from oil and grease. Bond speed is typically very fast so ensure that parts are properly aligned before dispensing. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little cyanoacrylate as possible should be used. Over application will result in slower cure speed and lower bond strength.
- Polyken 41 Citrus Cleaner / Adhesive Remover
Polyken 41 Citrus Cleaner / Adhesive Remover is an excellent degreaser and adhesive removal agent available in an aerosol spray can. Used to remove adhesive residue from many surfaces and also for multi-purpose cleaning and degreasing. The spray cleaner removes adhesive residue, ink, oil stains, road tar, rubber marks, decals, stickers, heel marks, graffiti, lipstick, release agents, and soap films. Polyken 41 is pleasantly scented by its natural citrus base. Use on metals, painted surfaces, glass, porcelain, plastics, and concrete. Test product in an inconspicuous area before full-scale application since it can damage some delicate surfaces such as gel coats, etc. Note: Polyken has discontinued Polyken 41 Citrus Cleaner and only limited stock remains.
- 3M Scotch FoamFast 74 Spray Adhesive (Orange)
3M FoamFast 74 Spray Adhesive is an aerosol adhesive used for bonding flexible urethane or latex foam together or for bonding many other materials like wood, metal, glass, fabrics, heavy papers and non-vinyl plastics (it is NOT recommended for bonding vinyl plastics). It is a fast drying adhesive and its high content of adhesive solids provides high coverage. 3M FoamFast 74 also has good moisture and temperature resistance to help protect bonds. Often used in recreational vehicles (RVs) for upholstery applications. Its volume is 22.6 fluid ounces (its net weight is 16.9 ounces). NOTE: No inventory now remains of 3M 74 FoamFast Orange; please see 3M Scotch Series 20 Aerosol Spray Adhesives for alternative 3M spray adhesive.
- Universal UNV75748 Permanent Glue Stick (Acid-Free)
Universal Office Products UNV75748 Permanent Glue Stick is a washable, non-toxic, acid-free glue stick which can be used on paper, cardboard, photos and fabric. The glue dries clear and wrinkle-free. Ideal for archival materials. ACMI/AP certified. Please note we do allow you to buy just one stick at a time so please order 12 if you'd like a full box.
- Wooster Floor Prep Cleaning Solution
Wooster Floor Prep is an alkaline solvent compound used for heavy-duty cleaning. It is an easy to handle, fast cleaning liquid designed for steam or spray cleaning as well as floor scrubbing machines and can be used in both interior and exterior applications. It is designed to clean areas subjected to heavy grease, oil and carbonaceous soils, and can be used to clean any type of surface. Wooster Floor-Prep has been approved by the U.S.D.A. for cleaning floors and walls in poultry, meat, rabbit and egg processing plants. Biodegradable and phosphate-free. To apply: Dilute 1/4 pint (4 fl. ounces) of Floor Prep to one gallon of warm-to-hot water (up to 160°F) - this amount of solution will clean approximately 30 to 40 square feet of area. Pour the cleaner over the area to be cleaned and allow to soak up to 15 minutes. After soaking, clean area with a power scrubber or agitate with a stiff bristled brush. Agitate until a foaming action occurs. Follow by two (2) thorough high-pressure water rinses, preferable hot. Floor Prep is a highly alkaline material. Direct contact may cause burns of eyes and skin. It is harmful if swallowed. Avoid contact with eyes, skin and clothing. Wear protective gloves, safety goggles and suitable protective clothing when handling. Wash thoroughly after handling. Do not take internally.