Shurtape PE-100 Temporary Flooring Tape is a specialty tape used on wood floors with water-based finishes to secure protective coverings and for creating temporary lines & boundaries on gym floors. PE-100 FloorMate tape comes up clean on a properly prepped/cured wood finish, is conformable enough to create curves, is more durable than paper tapes, removes without tearing or splintering, works for paint masking and is available in three colors.
Test tape in an inconspicuous area before using. It is for temporary use only. Finish damage is difficult and expensive to repair on wood floors, so assure preparation and finish application are done per finish manufacturer's recommendations. Allow finish to cure fully before applying tape. Remove tape slowly prior to 30 days on the floor.
LAB TESTED FINISHES
Water-based:
- Bona Traffic
- DuraSeal polyurethane
- Hillyard Contender
- Loba Hybrid
- Loba WS Easyfinish
- NewAge Full Court Press
- StreetShoe Basic
- StreetShoe 275
- Varathane Floor Finish
- X Terra
- Zinsser polyurethane
Solvent-based:
- Deft Defthane polyurethane
- Hillyard 350 Gym Finish
|
Shurtape PE-100 Temporary Flooring Tape Specifications- Adhesive: rubber How are adhesives different?
- Carrier/Backing: polyethylene film
- Thickness: 4.6 mils (carrier, adhesive) What is a mil?
- Adhesion: 15 ounces per inch (to stainless steel)
- Tensile Strength: 11 pounds per inch (longitudinal)
- Service/Operating Temperature: 32°F to 160°F
- Elongation: 500%
- Water Vapor Transmission Rate: 0.4 gm/100 sq in/24 hr
- Core: 3" diameter
* specifications are those given by manufacturers and are not tested for accuracy |
|
|
|
2 in. x 60 yds. (black, white)
Actual Size: 48mm x 55m | PE-100/260 | 24 | SINGLE ROLL (1 to 24 rolls) 1 TO 3 CASES(24 to 95 rolls) 4 TO 6 CASES(96 to 167 rolls) 7+ CASES(>= 168 rolls) | $11.91 $10.21 $10.04 $9.87 | * see individual roll price to left $245.04 $240.96 $236.88 |
|---|
|
2 in. x 60 yds. (pink)
Actual Size: 48mm x 55m | PE-100/260P | 24 | SINGLE ROLL (1 to 24 rolls) 7+ CASES(>= 168 rolls) | * 7 case
minimum required $9.87 |
$236.88 |
|---|
** special order sizes are not returnable (and non-cancelable if material has been ordered or cut before the cancellation request was made)
** special order sizes for this item typically ship direct from our supplier so will not ship together with stocked products
** minimum requirements are due to the fact that the product size is non-stock
** if a particular size has a minimum item requirement please only purchase that size in multiples of that minimum, e.g. if the minimum is 12 then purchase as 12, 24, 36, etc.
hot melt rubber (synthetic)
Offers the widest range of application flexibility available. Exhibits excellent processing performance whether manually or automatically applied. Has superior tensile strength, adhesion properties and holding force which ensures consistent, reliable seals. Hot melt adhesive will bond faster to a surface which is referred to as quick-grab or quick-stick. It typically has higher tack (will feel stickier to the touch), but is also softer. It has lower heat resistance, shear resistance, and sometimes UV resistance than an acrylic adhesive. NOTE: it is called hot melt because the adhesive is applied hot by the manufacturer and then hardens as it cools (you do not need to apply heat to the tape yourself).
natural rubber
Properties are similar to that of hot melt rubber, but natural rubber often holds where other adhesives won't (recycled fibers, dust, cold, heat and heavy loads). It provides good overall adhesion and moisture resistance.
acrylic
Offer excellent performance, especially for applications in temperatures less than 40°F and greater then 120°F. It provides excellent clarity, has high shear strength, is usually more permanent/durable even when exposed to moisture, and it ages well over extended periods in fluorescent and sunlight. Since it remains clear for the life of the application and does not yellow over time it is ideal for applications such as sealing white cartons. While it has good initial adhesion it does take 24-48 hours to cure and to achieve its maximum bond strength (has gradual adhesion buildup). Another difference between hot melt rubber and acrylic adhesive is if you fold tape over making the two adhesive sides touch the acrylic adhesive will remain attached to the carrier (e.g. paper, film) while a hot melt adhesive will stick to itself and pull off of the carrier. It is the best choice for clarity, UV resistance and aging characteristics.
silicone
Is great for extreme temperature applications since silicone adhesive can work in continuous operating temperatures from -100°F to 500°F. They also exhibit good chemical resistance, retain electrical properties, and remove cleanly with little or no residue.
zinc oxide
Zinc oxide based adhesive formula is a skin-friendly adhesive which is commonly used on sports medicine tapes.
1 mil = 1/1000 of an inchExamples: 1/16 inch = 62.5 mils; 1/32 inch = 31.25 mils
