- JVCC LPD-00 Table Top Label Protection Tape Dispenser
JVCC LPD-00 Table Top Label Protection Tape Dispenser is used to dispense label protection tape on a 3 inch diameter core and with a maximum roll diameter of 6-1/2 inches. Only one size dispenser is now available: one for tape up to 4 inches wide (the one that was for tape up to 6 inches wide has been discontinued by the manufacturer). Serrated knife is used to cut the tape. Plastic construction.
- JVCC LMD4 Aisle/Lane Marking Tape Dispenser
JVCC LMD4 Aisle/Lane Marking Tape Dispenser is a dispenser used to mark floors with vinyl tapes up to 4 inches wide on a 3 inch diameter core (accommodates rolls up to a maximum outside diameter of 6 inches). The dispenser is accommodating enough to lay down curves (to lay down a completely straight line you would want to trace along another object like a two by four). It is pre-assembled and individually cartoned. Metal construction.
- JVCC DCTTD2 Double-Coated Tape Table Top Dispenser
JVCC DCTTD2 Double-Sided Tape Table Top Dispenser dispenses double-coated (aka double-sided) tape or other tapes with a removable liner. One easy pull releases tape and peels off backing, rewinding it on the take-up spool. Tape roll holder and scrap rewind spool have independent adjustable brakes to insure proper performance with any weight tape. Clean cutting tempered steel blade. Holds rolls up to 2 inches wide with a maximum outside diameter of 7-1/4 inches. For rolls on a 3 inch diameter core. The dispenser is approximately 2 inches wide by 12 inches long. The dispenser color is typically either orange or blue depending on the color of the last lot received in.
- JVCC FTTD2 Foam Tape Table Top Dispenser
JVCC FTTD2 Foam Tape Table Top Dispenser dispenses foam tapes with a max outside diameter of 14-1/2 inches (370mm) while removing liner onto a spool. Peeled tape is ready to use and cut with scissor blades. Sliding arm allows for measuring preset lengths up to 500mm (acts like a measuring stick or gauge). Powder coated steel construction. For tape on a 3 inch core. This dispenser is also suitable to be used to dispense larger format Velcro Hook-N-Loop fastener tape. The spool has adjustable breaks. JVCC does not offer any replacement parts for this dispenser. The dimensions of the dispenser are 13 inches x 19-1/2 inches x 8 inches. Dispenser Instructions: Fix the core holder extension (top right in photo) my means of the two handwheels enclosed in the package. There are a few possible ways to thread the tape through the spools on the dispenser (click on the 'Download Instructions' icon below to see a few possibilities). The best set up of the dispenser is that which permits the complete rewind of the liner on the spool under minimum effort. The knobs of the core holder and the spool can be adjusted to change the torque required. .
- JVCC 925DC Double Coated Tape Dispenser
JVCC 925DC Double Coated Tape Dispenser is a hand-held tape dispenser for double-sided tapes (when adhesive is on both sides of the tape). Helps to apply tape to working surfaces while rewinding the liner on the take-up spool. Heavy formed steel frame for long life. Adjustable tension brakes on tape roll holder and scrap rewind spool insure proper performance with any tape weight. Has a serrated blade attached to the dispenser. This dispenser is not recommended for thick, difficult to cut tapes such as double-coated cloth/carpet tapes. Holds rolls up to 2" wide with maximum 5-1/2" diameter on 3" core. Application Instructions Take the tape's release liner around the rubber roller "before" the knife so it will not get cut. The tape goes over the knife up to the small roller on top, the liner bends around the larger roller, under the knife and back to the wind-up. You also have to adjust tensions on the unwind and wind up until it works correctly since every type of tape requires a different adjustment.