- 3M Scotch 4298 Adhesion Promoter [Sponge Applicator Packet]
3M 4298 Adhesion Promoter is a liquid primer used for most low surfaces energy plastics. This would include common low surface energy plastics used for automotive dash and interior trim applications (TPO, PPO, PP, PC, PC and ABS, etc.). It is specifically formulated to be used with 3M VHB Acrylic Foam Tapes. Since formulations and surface energies can vary for these types of materials, each application should be verified through testing. This adhesion promoter is supplied in an easy-to-use sponge applicator packet. Application Instructions The liquid contents of the packet should be completely used as soon as possible after opening. Hold packet upright and avoid squeezing an opened packet to prevent spillage of liquid contents. The packet can be opened by tearing across the top of the packet at the notches. This will expose the sponge applicator. Do not remove the sponge or squeeze a freshly opened packet. Handling the bottom section of the packet should enable application of 3M adhesion promoter 4298 with no mess. Apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. A wet coating thickness of 0.002 inch or less is recommended. Apply promoter only to areas that will be fully covered with tape. Although drying times may vary due to temperature and/or humidity, a drying time of 30 to 90 seconds is typically indicative of this thickness. The primer should be dry before applying tape. For best results, apply tape immediately after primer application or no more than one hour afterwards. Be sure the primed surface remains free from contaminants prior to tape application.
- 3M Scotch 111 Adhesion Promoter [Bottle]
3M 111 Adhesion Promoter, also referred to as AP111, is an isopropyl alcohol based primer solvent solution used to promote better and faster adhesion of 3M VHB Acrylic Foam Tapes to various surfaces including bare metals, galvanized steel, and painted surfaces. Since surfaces and paint formulations vary considerably, each application should be verified through testing. 3M 111 can clean and promote adhesion in one step provided the surface is relatively clean and free of wax, grease, oil, and loose particles. Coverage provided is approximately 19 square meters per liter based on 2 mil wet coating thickness. Can vary greatly depending on method of application. Drying time is approximately 1 minute depending on coating thickness, temperature, and humidity. Features & Benefits Increases tape adhesion build rate at both normal and cooler temperatures. Has non-offensive odor. Is very quick drying. Offers higher bond strength.
- 3M Scotch AP115 Silane Glass Treatment [Spray Bottle]
3M AP115 Silane Glass Treatment is used to promote adhesion of 3M Acrylic Foam VHB Tapes to uncoated glass surfaces. Glass is hydrophilic (water loving) in nature and may lead to performance issues over time in humid or wet environments due to water vapor undercutting the bondline and interfering with normal adhesion forces. 3M silane glass treatment AP115 treats the glass surface (acts as an adhesion promoter or primer) creating a hydrophobic surface that will act to protect the 3M VHB Tape bondline. Coverage provided is approximately 20 to 25 square feet per 4 fluid ounce bottle.
- 3M Scotch 08987 General Purpose Adhesive Cleaner
3M 08987 Adhesive Cleaner is a specially blended solvent in aerosol form used for removal of light paint overspray, adhesive residue, wax, grease, tree sap, dirt, road tar, oil and bugs. Will not harm most thoroughly cured automotive paint, vinyls, or fabrics when properly used. Part number 08987 Aerosol has a VOC content of 738 grams per liter (6.16 lbs per gallon).
- 3M Scotch 94 Tape Primer [Ampule]
3M 94 Tape Primer is an adhesion promoter for use in conjunction with 3M Acrylic Foam VHB Tapes. For use on many plastic, rubber, metal, polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, painted and bare metal substrates. Coverage provided is 600 square feet per gallon of primer . Application Instructions Shake 3M Primer 94 well before using (for the ampules need to squeeze in middle until hear pop to break the inside vessel). Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface. Allow 3M Primer 94 to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature. Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 applications of 3M Primer 94 for uniform coverage and good adhesion. Allow first application of primer to dry before applying the second coat.
- Polyken 41 Citrus Cleaner / Adhesive Remover
Polyken 41 Citrus Cleaner / Adhesive Remover is an excellent degreaser and adhesive removal agent available in an aerosol spray can. Used to remove adhesive residue from many surfaces and also for multi-purpose cleaning and degreasing. The spray cleaner removes adhesive residue, ink, oil stains, road tar, rubber marks, decals, stickers, heel marks, graffiti, lipstick, release agents, and soap films. Polyken 41 is pleasantly scented by its natural citrus base. Use on metals, painted surfaces, glass, porcelain, plastics, and concrete. Test product in an inconspicuous area before full-scale application since it can damage some delicate surfaces such as gel coats, etc.
- Duck Brand Adhesive Remover Applicator & Scraper
Duck Brand Adhesive Remover removes adhesive residue, tar, caulk, gum, crayon and more. One-step, no-mess bottle applicator with a built-in sponge and scraper. The remover works on many surfaces including windows, walls, floors, furniture, glass, carpet, metal and plastic (it is always recommended to test on an inconspicuous part of the surface first). Removes adhesive residue left behind by duct tape, masking tape, carpet tape, mounting tape, weather striping tape, stickers and labels. Has a fresh citrus scent. Application Instructions Use sponge applicator to apply remover. Place scraper cap back onto bottle. Let liquid sit for 20 to 30 seconds. Remove residue using the scraper. Wipe off excess liquid. Clean surface with soap and water.
- Wooster Floor Prep Cleaning Solution
Wooster Floor Prep is an alkaline solvent compound used for heavy-duty cleaning. It is an easy to handle, fast cleaning liquid designed for steam or spray cleaning as well as floor scrubbing machines and can be used in both interior and exterior applications. It is designed to clean areas subjected to heavy grease, oil and carbonaceous soils, and can be used to clean any type of surface. Wooster Floor-Prep has been approved by the U.S.D.A. for cleaning floors and walls in poultry, meat, rabbit and egg processing plants. Biodegradable and phosphate-free. Floor Prep is a highly alkaline material. Direct contact may cause burns of eyes and skin. It is harmful if swallowed. Avoid contact with eyes, skin and clothing. Wear protective gloves, safety goggles and suitable protective clothing when handling. Wash thoroughly after handling. Do not take internally. Application Instructions Dilute 1/4 pint (4 fl. ounces) of Floor Prep to one gallon of warm-to-hot water (up to 160°F) - this amount of solution will clean approximately 30 to 40 square feet of area. Pour the cleaner over the area to be cleaned and allow to soak up to 15 minutes. After soaking, clean area with a power scrubber or agitate with a stiff bristled brush. Agitate until a foaming action occurs. Follow by two (2) thorough high-pressure water rinses, preferable hot.