- 3M Scotch 4298 Adhesion Promoter [Sponge Applicator Packet]
3M 4298 Adhesion Promoter is a liquid primer used for most low surfaces energy plastics. This would include common low surface energy plastics used for automotive dash and interior trim applications (TPO, PPO, PP, PC, PC and ABS, etc.). It is specifically formulated to be used with 3M VHB Acrylic Foam Tapes. Since formulations and surface energies can vary for these types of materials, each application should be verified through testing. This adhesion promoter is supplied in an easy-to-use sponge applicator packet. Application Instructions The liquid contents of the packet should be completely used as soon as possible after opening. Hold packet upright and avoid squeezing an opened packet to prevent spillage of liquid contents. The packet can be opened by tearing across the top of the packet at the notches. This will expose the sponge applicator. Do not remove the sponge or squeeze a freshly opened packet. Handling the bottom section of the packet should enable application of 3M adhesion promoter 4298 with no mess. Apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. A wet coating thickness of 0.002 inch or less is recommended. Apply promoter only to areas that will be fully covered with tape. Although drying times may vary due to temperature and/or humidity, a drying time of 30 to 90 seconds is typically indicative of this thickness. The primer should be dry before applying tape. For best results, apply tape immediately after primer application or no more than one hour afterwards. Be sure the primed surface remains free from contaminants prior to tape application.
- Duck Brand Adhesive Remover Applicator & Scraper
Duck Brand Adhesive Remover removes adhesive residue, tar, caulk, gum, crayon and more. One-step, no-mess bottle applicator with a built-in sponge and scraper. The remover works on many surfaces including windows, walls, floors, furniture, glass, carpet, metal and plastic (it is always recommended to test on an inconspicuous part of the surface first). Removes adhesive residue left behind by duct tape, masking tape, carpet tape, mounting tape, weather striping tape, stickers and labels. Has a fresh citrus scent. Duck Brand Adhesive Remover Usage Instructions: Use sponge applicator to apply remover. Place scraper cap back onto bottle. Let liquid sit for 20 to 30 seconds. Remove residue using the scraper. Wipe off excess liquid. Clean surface with soap and water.
- Scapa 175 Cloth Tape
Scapa 175 Cloth Tape is a general purpose conformable cotton cloth tape single coated with a natural rubber adhesive. It's non-thermosetting adhesive and backing are suitable for skin contact. The tape is paintable. Uses of the Scapa 175 Cloth Tape include: motor coil winding; wire harness wrap and other bundling applications; general purpose tape for surfaces requiring a high degree of stain or corrosion resistance where high tensile strength is not required; electrical tape applications; and finger taping.
- Pro Tapes Pro Flex Patch & Shield Tape
Pro Tapes Pro Flex Patch & Shield Tape is an all weather, flexible butyl patch and shield repair tape. Its one of the heaviest, most aggressive sealing tapes available. Use to deal with leaks in virtually all roofing and metalized surfaces. The tape is easy to apply to any clean, dry surface. Also recommended for use when stopping leaks on mobile homes, RVs, rail cars, trucks, vans, garden sheds, gutters, tarpaulins and some unpressurized piping. Pro Flex is UV resistant for added longevity, VOC free, and conforms easily.
- 3M Scotch 08987 General Purpose Adhesive Cleaner
3M 08987 Adhesive Cleaner is a specially blended solvent in aerosol form used for removal of light paint overspray, adhesive residue, wax, grease, tree sap, dirt, road tar, oil and bugs. Will not harm most thoroughly cured automotive paint, vinyls, or fabrics when properly used. Part number 08987 Aerosol has a VOC content of 738 grams per liter (6.16 lbs per gallon).
- Nashua Stretch & Seal Self Fusing Silicone Tape
Nashua Stretch & Seal Self Fusing Silicone Tape, is an adhesive-free tape that fuses only to itself. This silicone rubber tape is suitable for dozens of applications where a good water-tight seal is needed. Applications for Nashua Stretch & Seal include: sealing pipes, electrical wiring, wires and hoses; covering sharp edges; protecting against rust and corrosion; wrapping tool handles; marking chain and rope. Stretch & Seal creates an instant, permanent water-tight seal (can even apply in wet conditions) and can withstand temperatures from -60°F to +500°F. Chemical and UV resistant. Can be kept in vehicles for emergency hose repairs. Easy to apply and to remove (is repositionable to achieve a proper seal) and no sticky adhesive residue left on surfaces. When applying the tape make sure it overlaps itself (since it only adheres to its own backing) and stretch/pull the tape tightly around the object.
- 3M Scotch SJ5300 Series Bumpon Self-Adhesive Bumpers
3M Bumpon SJ5300 Series Self-Adhesive Bumpers are pressure sensitive adhesive-backed polyurethane products that can be used as feet, stops, spacers and protectors in many applications. The urethane is a durable, resilient elastomer. The aggressive, high tack pressure sensitive adhesive is protected with a release liner making application fast and easy. The plasticizer-free urethane composition of the bumpons exhibit excellent skid resistance, long aging resiliency (will not crack or harden), abrasion resistance and resistance to marring and staining. Use 3M Bumpons almost anywhere slamming, scratching, nicking, scuffing, marring, sliding, vibration, or noise could be a problem for your product. Uses & Applications Feet on the bottom of blenders, desk top calculators, electronic cabinetry, telephones, keyboards, foot pedals, scales, clocks, speakers, dispensers and computers. Stops for cabinet doors, lids and drawers. Spacers for picture frames to provide alignment; for auto glass as an aid in assembly. Protectors for stacked glass and metal sheets. The tapered square bumpers are typically used for larger appliances and electronics while the smaller hemisphere and cylindrical shaped bumpons are usually used for phones, speakers and keyboards. The hexagon shaped bumpons are made from soft foam rollstock and are used in woodworking where a softer material is preferred. The SJ6553 quiet bumpons have a hexagonal cone shape and are ideal for use on cabinets and drawer fronts. Please note the black tapered square SJ5023 bumpons do not come retail packaged like the other packs, but just come on sheets with 36 bumpons on each sheet. The 0.312 inch x 0.085 inch clear hemisphere shaped bumpons come 96 per retail pack. The 0.50 inch x 0.140 inch cylindrical bumpons come 56 per retail pack. The 0.375 in. x 0.120 in. and the 0.433 inch x 0.125 inch hexagon bumpons come 132 per pack. Application Instructions Apply to any smooth, flat surface such as glass, metal, wood, smooth plaster, tile, etc. For best results surfaces must be clean and dry. Clean with a low strength solvent like isopropyl alcohol (rubbing alcohol) or heptane (white gas) with a clean cloth. Do not attempt to use on fabric, course concrete walls, rough sand finishes, loose paint or rough wallpaper. Remove paper liner from back of bumper. Avoid touching adhesive with fingers. Place bumper on desired location and press firmly to insure contact of adhesive.
- 3M Scotch 4411 Extreme Sealing Tape [40 mil]
3M Scotch 4411 Extreme Sealing Tape is a highly conformable single-side acrylic tape with a high performance ionomer backing which is designed for difficult sealing applications. The backing on this tape is an ionomer film that is very tough yet flexible and abrasion resistant. The very soft and thick acrylic adhesive has excellent sealing properties and good outdoor durability. This single coated tape is designed to seal over an existing joint, seam, or penetration. The adhesive is designed to adhere well to the ionomer film so that overlapping tape joints can be made while maintaining a strong seal.The tape gives you consistent thickness over using a liquid adhesive. Used for motor home leaks, roof and gutter holes / tears, transportation industry. Comes on a release liner on non-adhesive side to allow for easier unwind. Please note the translucent color is almost white because of the thickness of the tape. Features & Benefits Sticks on contact to many metals and plastics without drying time, dripping, oozing and clean up. Excellent high pressure water, moisture, and thermal shock resistance. Durable. Clear appearance, paintable. Application Instructions It is often required to overlap 3M Extreme Sealing Tape onto itself. In this case, the ionomer backing of the first piece is one of the substrates to which the second piece of tape is bonding. The tapes should overlap at least 3/4 inch. The ionomer does not need to be cleaned prior to bonding unless it has been contaminated with oil, dirt, grease, etc. If the bonding area of the ionomer has been contaminated, IPA/water can be used to clean the surface. A quick wipe of 3M 111 Adhesion Promoter on the ionomer is suggested for best performance of the overlapping tape. AP111 will approximately double Extreme Sealing Tape’s adhesion to its own ionomer backing. Firm pressure should be applied to all points of overlap between the two tapes to join the adhesives and create a robust seal.
- 3M Scotch 111 Adhesion Promoter [Bottle]
3M 111 Adhesion Promoter, also referred to as AP111, is an isopropyl alcohol based primer solvent solution used to promote better and faster adhesion of 3M VHB Acrylic Foam Tapes to various surfaces including bare metals, galvanized steel, and painted surfaces. Since surfaces and paint formulations vary considerably, each application should be verified through testing. 3M 111 can clean and promote adhesion in one step provided the surface is relatively clean and free of wax, grease, oil, and loose particles. Coverage provided is approximately 19 square meters per liter based on 2 mil wet coating thickness. Can vary greatly depending on method of application. Drying time is approximately 1 minute depending on coating thickness, temperature, and humidity. Features & Benefits Increases tape adhesion build rate at both normal and cooler temperatures. Has non-offensive odor. Is very quick drying. Offers higher bond strength.
- JVCC TL-4 Tie Line
JVCC TL-4 Tie Line is also known as "trick" line or "sash cord". The #4 cotton tie line is coated which allows for more permanent use with greater holding power. Comes in reels of various sizes.
- 3M Scotch 94 Tape Primer [Ampule]
3M 94 Tape Primer is an adhesion promoter for use in conjunction with 3M Acrylic Foam VHB Tapes. For use on many plastic, rubber, metal, polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, painted and bare metal substrates. Coverage provided is 600 square feet per gallon of primer.
- 3M Scotch AP115 Silane Glass Treatment [Spray Bottle]
3M AP115 Silane Glass Treatment is used to promote adhesion of 3M Acrylic Foam VHB Tapes to uncoated glass surfaces. Glass is hydrophilic (water loving) in nature and may lead to performance issues over time in humid or wet environments due to water vapor undercutting the bondline and interfering with normal adhesion forces. 3M silane glass treatment AP115 treats the glass surface (acts as an adhesion promoter or primer) creating a hydrophobic surface that will act to protect the 3M VHB Tape bondline. Coverage provided is approximately 20 to 25 square feet per 4 fluid ounce bottle.
- Duck Brand Fiberglass Carpet Double-Sided Tape [Indoor/Outdoor]
Duck Brand Fiberglass Carpet Tape is a double-sided fiberglass tape used for permanent carpet installation. Fiberglass is moisture and mildew resistant so it is ideal for high traffic areas where moisture is a problem such as bathrooms, basements and decks. For both indoor and outdoor use. Since this tape is for permanent installations removal could cause damage to not only the floor but also to the carpet. Instructions To Apply Double-Sided Fiberglass Carpet Tape: Thoroughly clean and dry floor surface. Apply tape, liner side up, pressing firmly to floor. Roll or fold one half or carpet cut to fit area back over itself. Remove tape liner, then roll or fold carpet back down to floor, pressing firmly for good adhesion. Then repeat for the other half of carpet.
- Polyken 41 Citrus Cleaner / Adhesive Remover
Polyken 41 Citrus Cleaner / Adhesive Remover is an excellent degreaser and adhesive removal agent available in an aerosol spray can. Used to remove adhesive residue from many surfaces and also for multi-purpose cleaning and degreasing. The spray cleaner removes adhesive residue, ink, oil stains, road tar, rubber marks, decals, stickers, heel marks, graffiti, lipstick, release agents, and soap films. Polyken 41 is pleasantly scented by its natural citrus base. Use on metals, painted surfaces, glass, porcelain, plastics, and concrete. Test product in an inconspicuous area before full-scale application since it can damage some delicate surfaces such as gel coats, etc.
- JVCC SRT-700 Silicone Rubber Tape
JVCC SRT-700 Silicone Rubber Tape is a self adhering, self bonding (an adhesive-free tape that fuses only to itself) red triangular silicone tape. It offers excellent electrical insulation properties, moisture, chemical and UV resistance. It's self bonding properties offer excellent conformability and adherence to irregular and nontraditional surfaces. JVCC SRT-700 silicone tape is made of a special unsupported silicone rubber compound which readily adheres to itself when wrapped under tension and forms a homogeneous mass within 24 hours. The adhesion can be accelerated with heat and pressure. When applying the tape make sure it overlaps itself (since it only adheres to its own backing) and stretch/pull the tape tightly around the object (the tape has a white guide line down the middle to help in overlapping it correctly). The tape creates an instant, permanent water-tight seal and can withstand temperatures from -65°F to +500°F. No adhesive (self bonding) insures no residue. The tape has a triangular thickness so it is thinner at the edges and thicker in the middle. Applications for JVCC SRT-700 include: watertight insulated over wrap of any electrical or wiring connection, indoors and out; automotive and general fluid hose repair (keep in vehicle for emergency repairs); replacement for heat shrinkable tubing; and replacement for electrical tape on marine applications.
- JVCC MAG-01-W Writeable Magnetic Tape [No Adhesive]
JVCC MAG-01-W Writeable Magnetic Tape is comprised of a multipole one face flexible magnet (composite of strontium and/or barium ferrite particles oriented with a thermoplastic polymer matrix). These permanent magnets remain magnetized indefinitely if not subjected to a demagnetizing force. This tape is not returnable for this reason. The tapes marked as write-on/wipe-off have a non-porous, smooth, and shiny white vinyl surface. Writeable with a dry erase marker and just wipe off. Applications include warehouse labels, store/retail shelf labels, schedule/planning boards, and control charts. The tapes marked as writeable have a porous, writeable, screen-printable matte white vinyl surface. Writeable with a permanent marker, or with a water soluble marker (wipe off with a damp rag) for non-permanent applications. Note, wiping off will gray surface over time. Applications include: automobile signs, marketing displays/premiums, business cards, warehouse/barcode labels, and control charts.
- JVCC SCP-04 Silicone-Coated Paper Separator Sheets
JVCC SCP-04 Silicone-Coated Paper Separator Sheets are paper sheets which are coated with silicone. Tapes with rubber or acrylic adhesive will not stick to the silicone so if you need to send pre-cut tape pieces to a customer they can be used for that purpose. These are the same sheets we use in our layer-packed boxes (e.g. a case of duct tape or gaffers tape) as separators between the layers. They are purchasable by the pack and 20 sheets or strips come per pack.
- JVCC RW-32 Roller Wrap Tape [Dimpled Siliconized Cloth]
JVCC RW-32 Roller Wrap Tape is an embossed or dimpled siliconized cloth tape coated with an acrylic adhesive system. It is designed to protect web rollers from the buildup of adhesives, inks, coatings, and other materials in the adhesive tape manufacturing, general converting, printing, textiles and paper & film industries. It is sometimes referred to as the printer's friend. By reducing buildup on idler, feed, and take-up rollers, The specially formulated adhesive on the tape minimizes residue upon removal minimizing the amount of roller clean up required when the tape is changed which extends the life of the roller itself. JVCC RW-32 Web Roller Wrap Tape significantly reduces clean-up and maintenance times making production processes much more efficient. It's high co-efficient of friction provides an anti-slip surface and allows it to grip the web and keeps materials moving while preventing the build-up of inks, adhesives and coatings (anti-stick). Also has excellent continuous temperature resistance.
- JVCC PolyPro Twisted Rope
JVCC PolyPro Twisted Rope is superior to manila rope and conventional polypropylene mono filament rope is several respects This rope is manufactured from extruded copolymer (polypropylene and polyethylene) fibers whose unique properties result in ropes that, size for size, are almost triple the strength of traditional high quality manila rope and twice the strength of conventional polypropylene rope. Not only is PolyPro rope far stronger, but it also weighs much less, making it easier to handle. It also has very good resistance to rot mildew, acids and alkalis. It does not harden with age, experience any loss of strength, either from wetness or from drying, and has among the lowest percent elongation. The abrasion resistance of the rope is superior to manila and polypropylene rope and (a particularly important consideration for rigging application) withstands shock load much better than manila rope as well. Unused PolyPro rope has a slightly stiff feeling as it comes off the coil, but it rapidly becomes highly pliable once it is placed in service. After running only a short time over sheaves, the rope will develop a surface "fuzz" which makes for a silky feel and excellent handling characteristics, unlike polypropylene rope which is coarse and slippery on handling.
- JVCC TS-3 Pipe Thread Seal Tape
JVCC TS-3 Pipe Thread Seal Tape is a multi-purpose non-adhesive thread sealing tape. TS-3 is 100% virgin PTFE and comes in a labeled plastic spool. Used to lubricates joints, making them easy to assemble for a leak proof seal. Thread Sealant Tape extends fatigue life of sealed connections and eliminates system contamination common with messy liquid and paste sealants. Also referred to as "Ribbon Dope" tape.
- JVCC MAG-01 Magnetic Tape [With Adhesive / 1/32" thickness]
JVCC MAG-01 Magnetic Tape is a flexible magnet mounted on a thin polyester film which has been coated on one side with an aggressive rubber based pressure sensitive adhesive. Tape is supplied self-wound on a semi-bleached kraft paper liner. The magnet is comprised of a multipole one face flexible magnet (composite of strontium and/or barium ferrite particles oriented with a thermoplastic polymer matrix). These permanent magnets remain magnetized indefinitely if not subjected to a demagnetizing force. This tape is not returnable for this reason. Please note this magnet has a thickness of 30 mils as noted in the product specializations so is slightly under 1/32" in thickness. As such it would not be able to hold up heavier weight items like heavy-weight fabric (see the 1/16" thick JVCC MAG-02 for heavier weight items). One way we've found to increase the magnetic attraction is to cut some MAG-01 into two pieces and then peel off the release liner to expose the adhesive side and then adhere to the two substrates. Then bring both magnetic sides together which typically creates a stronger magnetic bond. As noted above JVCC MAG-01 is a single-faced multi-pole magnet so one side has a polarity and the other side is coated with an adhesive. The side with polarity would be attracted to a magnet of the opposite polarity. The tape is NOT attracted to itself (it repels) since it would need a magnet of the opposite polarity to attract.
- JVCC MAG-02 Magnetic Tape [With Adhesive / 1/16" thickness]
JVCC MAG-02 Magnetic Tape is a flexible magnet mounted on a thin 4.5 mil polyester film which has been coated on one side with an aggressive acrylic based pressure sensitive adhesive. The indoor/outdoor adhesive the tape is coated with is for bonding applications where outstanding adhesion, high shear and good solvent and UV resistance are required. The tape is supplied self-wound on a semi-bleached kraft paper liner. The magnet is comprised of a multipole one face flexible magnet (composite of strontium and/or barium ferrite particles oriented with a thermoplastic polymer matrix). These permanent magnets remain magnetized indefinitely if not subjected to a demagnetizing force. This tape is not returnable for this reason. Please note this magnet has a thickness of 60 mils as noted in the product specializations so is slightly under 1/16" in thickness. As such it would hold up heavier weight items better than the 1/32" thick MAG-01 Magnetic Tape we also sell. Also as noted above JVCC MAG-02 is a single-faced multi-pole magnet so one side has a polarity and the other side is coated with an adhesive. The side with polarity would be attracted to a magnet of the opposite polarity. The tape is NOT attracted to itself (it repels) since it would need a magnet of the opposite polarity to attract.
- Duck Brand Carpet Seaming Indoor/Outdoor Fiberglass Tape
Duck Brand Carpet Seaming Tape is a single-sided fiberglass tape with an adhesive backing on one side. The fiberglass carrier on the tape is moisture and mildew resistant. Duck Carpet Seaming Tape can be used both indoors and outdoors. The tape helps to quickly join carpet pieces together without special tools or irons - the tape is self stick and there is no liner to remove. Recommended for permanent applications. Application Instructions Position carpet as desired, butting together edges to be seamed. Fold back edges and begin to unroll tape into the exposed seaming area non-adhesive side to the floor. Caution: the adhesive on the tape is extremely aggressive and may become permanent with initial contact to carpet backing. Be certain to center the tape correctly as you begin. Continue to unroll tape several feet at a time pressing seam edges back down into adhesive firmly for good adhesion.
- Duck Brand Drywall Joint Self-Adhesive Fiberglass Tape
Duck Brand Drywall Joint Tape is a 100% fiberglass mesh tape. It is self-adhesive and repositionable. Also strong, fast and easy to use - no need to re-apply compound to joints. Used for repairing cracks and small holes. Instructions for Taping Drywall (Sheetrock) Joints: Clean surface of dust and dirt. Position tape over seam and cut to exact length. When seaming drywall/wallboard joints, use only quick setting joint compound. For best results maintain room temperature between 50° - 70°F. Apply joint compound working it through the mesh. Let dry to manufacturer's instructions and sand smooth. Apply a second, thinner coat wider than the first feathering edges outward. Let dry and sand smooth. Instructions for Repairing Cracks: Slightly open up crack to a width of 1/8" and fill with ready mix or any setting compound. Let dry to manufacturer's instructions. Clean and sand surface. Apply joint tape to the repair area; overlapping the end of each crack by 1" or more. Spread compound down the crack, working it through the mesh. let dry and sand smooth. For a finished appearance apply a second, thinner coat wider than the first. Let dry and sand smooth. Instructions for Patching Holes: Clean and sand surface. Cut two pieces of joint tape 2" longer than the hole dimensions. Apply tape over the hole in a criss-cross manner so entire opening is covered by both layers. Depress joint tape 1/4" into hole and fill with ready mix or any setting compound. Let dry to manufacturer's instructions and sand smooth. For a finished appearance apply a second, thinner coat wider than the first. Let dry and sand smooth.
- Berry Plastics 509W Thread Seal Tape
Covalence 509W Thread Seal Tape is a multi-purpose non-adhesive thread sealing tape. It is a self-lubricating tape for wrapping threads at pipe connections making them easy to assemble and disassemble. Thread Seal Tape extends fatigue life of sealed connections and eliminates system contamination common with messy liquid and paste sealants. Product can also be used on a number of other maintenance type applications. It is easy to use and has an unlimited shelf-life. Also known as "Thread Sealant Tape" and "Ribbon Dope".
- Jaybird & Mais ICE Instant Ice Pack
Jaybird & Mais ICE Instant Ice Pack is a disposable ice compress in a sturdy two-ply poly bag which is convenient for travel. On average will stay cold for 20 minutes once activated. The ice packs should not be exposed to over 100°F temperatures for extended periods of time. Contains ammonium nitrate and water. Directions for use: Shake contents to the bottom of the bag. Locate the inner pouch and squeeze firmly to break. Shake gently to assure complete activation. Wrap in a soft cloth and apply (packs are double-bagged however as a safety precaution direct skin contact should be avoided in case bag gets punctured).
- JVCC PR-1 Packing List Envelope
JVCC PR-1 Packing List Envelopes come 1,000 per box and each envelope is 4-1/2 inches x 5-1/2 inches (usable space within each envelope for the packing slip is 4 inches x 5 inches). Side loading envelope printed with "PACKING LIST ENCLOSED" black on orange background panel. Just peel off the main paper release liner to get at pressure sensitive adhesive side and then apply to box (or insert your packing slip into the envelope and then peel off release liner and apply to your box). Then insert your packing slip and then remove the side paper release liner to secure flap down to box..
- Pro Tapes Pro-Matte Wrap Black Foil
Pro Tapes Pro-Matte Wrap Black Foil is a matte-black, opaque aluminum NON-ADHESIVE foil wrap that masks light leaks and eliminates reflections. Because it won't burn or melt, it's suitable for a wide range of applications: lighting decorators/engineers can use it to create shadows, form barn doors, adapt gobos, mask light spill and much more. Is boxed in an easy-to-use dispenser.
- Scapa RollerMate P2420 Silicone Rubber Coated Cloth Tape
Scapa RollerMate P2420 Silicone Rubber Coated Cloth Tape is an embossed or dimpled siliconized cloth coated with a solvent-based rubber/resin adhesive system. It is designed to protect web rollers from the buildup of adhesives, inks, coatings, and other materials in the coating, converting, and printing industries. By reducing buildup on idler, feed, and take-up rollers, RollerMate significantly reduces clean-up and maintenance times making production processes much more efficient. The specially formulated adhesive on RollerMate minimizes residue upon removal minimizing the amount of roller clean up required when the tape is changed which extends the life of the roller itself. The tape is more cost-effective than factory-applied coatings and competitive roller wraps. P2420's high co-efficient of friction provides an anti-slip surface and allows it to grip the web and keeps materials moving while preventing the build-up of inks, adhesives and coatings (anti-stick). Has excellent continuous temperature resistance.
- Wooster Floor Prep Cleaning Solution
Wooster Floor Prep is an alkaline solvent compound used for heavy-duty cleaning. It is an easy to handle, fast cleaning liquid designed for steam or spray cleaning as well as floor scrubbing machines and can be used in both interior and exterior applications. It is designed to clean areas subjected to heavy grease, oil and carbonaceous soils, and can be used to clean any type of surface. Wooster Floor-Prep has been approved by the U.S.D.A. for cleaning floors and walls in poultry, meat, rabbit and egg processing plants. Biodegradable and phosphate-free. Floor Prep is a highly alkaline material. Direct contact may cause burns of eyes and skin. It is harmful if swallowed. Avoid contact with eyes, skin and clothing. Wear protective gloves, safety goggles and suitable protective clothing when handling. Wash thoroughly after handling. Do not take internally. Application Instructions Dilute 1/4 pint (4 fl. ounces) of Floor Prep to one gallon of warm-to-hot water (up to 160°F) - this amount of solution will clean approximately 30 to 40 square feet of area. Pour the cleaner over the area to be cleaned and allow to soak up to 15 minutes. After soaking, clean area with a power scrubber or agitate with a stiff bristled brush. Agitate until a foaming action occurs. Follow by two (2) thorough high-pressure water rinses, preferable hot.