- 3M Scotch 4298 Adhesion Promoter [Sponge Applicator Packet]
3M 4298 Adhesion Promoter is a liquid primer used for most low surfaces energy plastics. This would include common low surface energy plastics used for automotive dash and interior trim applications (TPO, PPO, PP, PC, PC and ABS, etc.). It is specifically formulated to be used with 3M VHB Acrylic Foam Tapes. Since formulations and surface energies can vary for these types of materials, each application should be verified through testing. This adhesion promoter is supplied in an easy-to-use sponge applicator packet. Application Instructions The liquid contents of the packet should be completely used as soon as possible after opening. Hold packet upright and avoid squeezing an opened packet to prevent spillage of liquid contents. The packet can be opened by tearing across the top of the packet at the notches. This will expose the sponge applicator. Do not remove the sponge or squeeze a freshly opened packet. Handling the bottom section of the packet should enable application of 3M adhesion promoter 4298 with no mess. Apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. A wet coating thickness of 0.002 inch or less is recommended. Apply promoter only to areas that will be fully covered with tape. Although drying times may vary due to temperature and/or humidity, a drying time of 30 to 90 seconds is typically indicative of this thickness. The primer should be dry before applying tape. For best results, apply tape immediately after primer application or no more than one hour afterwards. Be sure the primed surface remains free from contaminants prior to tape application.
- 3M Scotch 111 Adhesion Promoter [Bottle]
3M 111 Adhesion Promoter, also referred to as AP111, is an isopropyl alcohol based primer solvent solution used to promote better and faster adhesion of 3M VHB Acrylic Foam Tapes to various surfaces including bare metals, galvanized steel, and painted surfaces. Since surfaces and paint formulations vary considerably, each application should be verified through testing. 3M 111 can clean and promote adhesion in one step provided the surface is relatively clean and free of wax, grease, oil, and loose particles. Coverage provided is approximately 19 square meters per liter based on 2 mil wet coating thickness. Can vary greatly depending on method of application. Drying time is approximately 1 minute depending on coating thickness, temperature, and humidity. Features & Benefits Increases tape adhesion build rate at both normal and cooler temperatures. Has non-offensive odor. Is very quick drying. Offers higher bond strength.
- Pro Tapes Pro Flex Patch & Shield Tape
Pro Tapes Pro Flex Patch & Shield Tape is an extremely durable, flexible, all-weather butyl-backed adhesive tape, specially made for reliable repairs. This heavy-duty, VOC-free tape is UV resistant for superior long-term performance. It conforms well and can be used to stop leaks in many materials such as metal surfaces and in roofing. It also adheres well to timber. Once surface is clean and dry, this Pro Flex tape applies easily. Product Applications Effectively stops leaks in and makes repairs to: Metalized surfaces Roofing materials RVs, mobile homes, rail cars, vans and trucks Gutters Garden sheds Windows Tarpaulins Gel cushion floor mats Certain kinds of unpressurized pipes Below grade concrete wall penetrations for water Flashing of a deck joist Rubber dust covers on automobiles Chimney flashing Motorcycle saddle bag Other uses: Seal glass to asphalt shingles Seal links in plastic downspout Many other household projects
- Nashua Stretch & Seal Self Fusing Silicone Tape
Nashua Stretch & Seal Self Fusing Silicone Tape, is an adhesive-free tape that fuses only to itself. This silicone rubber tape is suitable for dozens of applications where a good water-tight seal is needed. Applications for Nashua Stretch & Seal include: sealing pipes, electrical wiring, wires and hoses; covering sharp edges; protecting against rust and corrosion; wrapping tool handles; marking chain and rope. Stretch & Seal creates an instant, permanent water-tight seal (can even apply in wet conditions) and can withstand temperatures from -60°F to +500°F. Chemical and UV resistant. Can be kept in vehicles for emergency hose repairs. Easy to apply and to remove (is repositionable to achieve a proper seal) and no sticky adhesive residue left on surfaces. When applying the tape make sure it overlaps itself (since it only adheres to its own backing) and stretch/pull the tape tightly around the object.
- JVCC SCP-04 Silicone-Coated Paper Separator Sheets
With JVCC SCP-04 Silicone-Coated Paper Separator Sheets, companies can send pre-cut tape pieces to their customers. These separator sheets are paper sheets which have been coated with silicone. Rubber or acrylic adhesive tapes will not stick to the silicone, so they can be used for safe transport of pre-cut tape pieces for special packaging applications. These are the same premium quality sheets that are used in our layer-packed boxes, such as a case of gaffers tape or duct tape, as separator sheets between the layers. We sell these silicone paper separator sheets by the pack, with 20 sheets or strips in each pack. Product Applications Easy product returns or exchanges Electronic assemblies As part of an assembly kit for manufactured products Product installation kit POS display mounting FindTape has the largest selection of specialty tapes and adhesives available anywhere, and we offer them at affordable prices. You'll discover tapes for home, business and industrial use, such as electrical tape, packaging tape, double sided tape, Velcro tape, paper and masking tape, glow tape, foam tape, ATG products and much more.
- Scapa 175 Cloth Tape
Scapa 175 Cloth Tape is a general purpose conformable cotton cloth tape single coated with a natural rubber adhesive. It's non-thermosetting adhesive and backing are suitable for skin contact. The tape is paintable. Uses of the Scapa 175 Cloth Tape include: motor coil winding; wire harness wrap and other bundling applications; general purpose tape for surfaces requiring a high degree of stain or corrosion resistance where high tensile strength is not required; electrical tape applications; and finger taping.
- 3M Scotch 4411 Extreme Sealing Tape [40 mil]
3M Scotch 4411 Extreme Sealing Tape is a highly conformable single-side acrylic tape with a high performance ionomer backing which is designed for difficult sealing applications. The backing on this tape is an ionomer film that is very tough yet flexible and abrasion resistant. The very soft and thick acrylic adhesive has excellent sealing properties and good outdoor durability. This single coated tape is designed to seal over an existing joint, seam, or penetration. The adhesive is designed to adhere well to the ionomer film so that overlapping tape joints can be made while maintaining a strong seal.The tape gives you consistent thickness over using a liquid adhesive. Used for motor home leaks, roof and gutter holes / tears, transportation industry. Comes on a release liner on non-adhesive side to allow for easier unwind. Please note the translucent color is almost white because of the thickness of the tape. Features & Benefits Sticks on contact to many metals and plastics without drying time, dripping, oozing and clean up. Excellent high pressure water, moisture, and thermal shock resistance. Durable. Clear appearance, paintable. Application Instructions It is often required to overlap 3M Extreme Sealing Tape onto itself. In this case, the ionomer backing of the first piece is one of the substrates to which the second piece of tape is bonding. The tapes should overlap at least 3/4 inch. The ionomer does not need to be cleaned prior to bonding unless it has been contaminated with oil, dirt, grease, etc. If the bonding area of the ionomer has been contaminated, IPA/water can be used to clean the surface. A quick wipe of 3M 111 Adhesion Promoter on the ionomer is suggested for best performance of the overlapping tape. AP111 will approximately double Extreme Sealing Tape’s adhesion to its own ionomer backing. Firm pressure should be applied to all points of overlap between the two tapes to join the adhesives and create a robust seal.
- 3M Scotch AP115 Silane Glass Treatment [Spray Bottle]
3M AP115 Silane Glass Treatment is used to promote adhesion of 3M Acrylic Foam VHB Tapes to uncoated glass surfaces. Glass is hydrophilic (water loving) in nature and may lead to performance issues over time in humid or wet environments due to water vapor undercutting the bondline and interfering with normal adhesion forces. 3M silane glass treatment AP115 treats the glass surface (acts as an adhesion promoter or primer) creating a hydrophobic surface that will act to protect the 3M VHB Tape bondline. Coverage provided is approximately 20 to 25 square feet per 4 fluid ounce bottle.
- JVCC Dry Erase Office Tape [Silver]
JVCC Dry Erase Tape is a silver colored metallized (aluminized) polyester mylar film which can be written on with a wet or dry erase marker. A great tape for crafting, decorating and labeling anywhere you can place tape and need whiteboard functionality.
- JVCC TS-35 Pipe Thread Seal Tape [3.5 mil]
JVCC TS-35 Pipe Thread Seal Tape is a multi-purpose non-adhesive thread sealing tape. TS-35 is a 3.5 mil thick 100% virgin PTFE and comes in a labeled plastic spool. Comes in both standard and high density options. Used to lubricates joints, making them easy to assemble for a leak proof seal. Thread sealant Ttpe extends fatigue life of sealed connections and eliminates system contamination common with messy liquid and paste sealants. Also referred to as "Ribbon Dope" tape.
- 3M Scotch 94 Tape Primer [Ampule]
3M 94 Tape Primer is an adhesion promoter for use in conjunction with 3M Acrylic Foam VHB Tapes. For use on many plastic, rubber, metal, polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, painted and bare metal substrates. Coverage provided is 600 square feet per gallon of primer . Application Instructions Shake 3M Primer 94 well before using (for the ampules need to squeeze in middle until hear pop to break the inside vessel). Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface. Allow 3M Primer 94 to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature. Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 applications of 3M Primer 94 for uniform coverage and good adhesion. Allow first application of primer to dry before applying the second coat.
- Polyken 41 Citrus Cleaner / Adhesive Remover
Polyken 41 Citrus Cleaner / Adhesive Remover is an excellent degreaser and adhesive removal agent available in an aerosol spray can. Used to remove adhesive residue from many surfaces and also for multi-purpose cleaning and degreasing. The spray cleaner removes adhesive residue, ink, oil stains, road tar, rubber marks, decals, stickers, heel marks, graffiti, lipstick, release agents, and soap films. Polyken 41 is pleasantly scented by its natural citrus base. Use on metals, painted surfaces, glass, porcelain, plastics, and concrete. Test product in an inconspicuous area before full-scale application since it can damage some delicate surfaces such as gel coats, etc.
- 3M Scotch 08987 General Purpose Adhesive Cleaner
3M 08987 Adhesive Cleaner is a specially blended solvent in aerosol form used for removal of light paint overspray, adhesive residue, wax, grease, tree sap, dirt, road tar, oil and bugs. Will not harm most thoroughly cured automotive paint, vinyls, or fabrics when properly used. Part number 08987 Aerosol has a VOC content of 738 grams per liter (6.16 lbs per gallon).
- Duck Brand Fiberglass Carpet Double-Sided Tape [Indoor/Outdoor]
Duck Brand Fiberglass Carpet Tape is a double-sided fiberglass tape used for permanent carpet installation. Fiberglass is moisture and mildew resistant so it is ideal for high traffic areas where moisture is a problem such as bathrooms, basements and decks. For both indoor and outdoor use. Since this tape is for permanent installations removal could cause damage to not only the floor but also to the carpet. Instructions To Apply Double-Sided Fiberglass Carpet Tape Thoroughly clean and dry floor surface. Apply tape, liner side up, pressing firmly to floor. Roll or fold one half or carpet cut to fit area back over itself. Remove tape liner, then roll or fold carpet back down to floor, pressing firmly for good adhesion. Then repeat for the other half of carpet.
- Duck Brand Adhesive Remover Applicator & Scraper
Duck Brand Adhesive Remover removes adhesive residue, tar, caulk, gum, crayon and more. One-step, no-mess bottle applicator with a built-in sponge and scraper. The remover works on many surfaces including windows, walls, floors, furniture, glass, carpet, metal and plastic (it is always recommended to test on an inconspicuous part of the surface first). Removes adhesive residue left behind by duct tape, masking tape, carpet tape, mounting tape, weather striping tape, stickers and labels. Has a fresh citrus scent. Application Instructions Use sponge applicator to apply remover. Place scraper cap back onto bottle. Let liquid sit for 20 to 30 seconds. Remove residue using the scraper. Wipe off excess liquid. Clean surface with soap and water.
- 3M Scotch SJ Series Bumpon Self-Adhesive Bumpers
3M Bumpon SJ Series Self-Adhesive Bumpers are pressure sensitive adhesive-backed polyurethane products that can be used as feet, stops, spacers and protectors in many applications. The urethane is a durable, resilient elastomer. The aggressive, high tack pressure sensitive adhesive is protected with a release liner making application fast and easy. The plasticizer-free urethane composition of the bumpons exhibit excellent skid resistance, long aging resiliency (will not crack or harden), abrasion resistance and resistance to marring and staining. Use 3M Bumpons almost anywhere slamming, scratching, nicking, scuffing, marring, sliding, vibration, or noise could be a problem for your product. Uses & Applications Feet on the bottom of blenders, desk top calculators, electronic cabinetry, telephones, keyboards, foot pedals, scales, clocks, speakers, dispensers and computers. Stops for cabinet doors, lids and drawers. Spacers for picture frames to provide alignment; for auto glass as an aid in assembly. Protectors for stacked glass and metal sheets. The tapered square bumpers are typically used for larger appliances and electronics while the smaller hemisphere and cylindrical shaped bumpons are usually used for phones, speakers and keyboards. The hexagon shaped bumpons are made from soft foam rollstock and are used in woodworking where a softer material is preferred. The quiet bumpons have a hexagonal cone shape and are ideal for use on cabinets and drawer fronts. Adhesive Description A-20 Acrylic, excellent shear strength properties, good on high surface energy substrates like metal, glass and high surface energy plastics. R-25 Synthetic Rubber, very high tack adhesive, excellent initial adhesion, works best on low like textured or powder-coated paint and polypropylene. R-30 Natural Rubber, high tack, good initial adhesion, also good for low surface energy substrates, versatile adhesive that works well on most surfaces. Product Color Shape Width x Height Adhesive Example Application Bumpons Per Pack Packaging SJ5302 clear hemisphere 0.312 in. x 0.085 in. A-20 mobile handhelds/organizers 96 retail-pack SJ5376 clear cylindrical 0.315 in. x 0.11 in. A-20 trophy and award feet 56 *** not retail-packed SJ5306 clear hemisphere 0.375 in. x 0.15 in. A-20 trophy and award feet 96 *** not retail-packed SJ6553 clear (quiet) hexagon base, cone top 0.433 in. x 0.120 in. R-25 cabinet doors & drawers 132 retail-pack SJ5201 light brown hexagon 0.433 in. x 0.125 in. R-25 inside door frame stops 132 retail-pack SJ5312 clear cylindrical 0.50 in. x 0.140 in. A-20 picture frames 56 retail-pack SJ5412 white cylindrical 0.50 in. x 0.140 in. A-20 picture frames 56 retail-pack SJ5023 black tapered square 0.81 in. x 0.3 in. R-30 coffee maker feet 36 *** not retail-packed SJ5009 black cylindrical shape, concave top 0.88 in. x 0.4 in. R-30 small kitchen appliance feet 24 *** not retail-packed Application Instructions Apply to any smooth, flat surface such as glass, metal, wood, smooth plaster, tile, etc. For best results surfaces must be clean and dry. Clean with a low strength solvent like isopropyl alcohol (rubbing alcohol) or heptane (white gas) with a clean cloth. Do not attempt to use on fabric, course concrete walls, rough sand finishes, loose paint or rough wallpaper. Remove paper liner from back of bumper. Avoid touching adhesive with fingers. Place bumper on desired location and press firmly to insure contact of adhesive.
- 3M Scotch 130C Linerless Rubber Splicing Tape
3M Scotch 130C Linerless Rubber Splicing Tape is a highly conformable, linerless Ethylene Propylene Rubber (EPR), high-voltage insulating tape that provides excellent thermal dissipation of splice heat. The tape is designed for use in splicing and terminating wires and cables. Rated up to 194 °F continuous operating temperatures and short-term 266°F overload service. It also meets industry specifications and has excellent physical and electrical properties (which are unaffected by the degree of stretch), which helps provide immediate moisture seal and void-free buildups. The tape is self-fusing which means it is an adhesive-free tape that fuses only to itself (no sticky residue left on surfaces). Applications for Scotch 130C include: primary insulation for splicing all types of solid dielectric insulated cables through 69 kV; primary insulation for building stress cones on all types of solid dielectric insulated cables up to 35 kV; jacketing (secondary insulation) on high-voltage splices and terminations; moisture-sealing electrical connections; bus bar insulation; end-sealing high-voltage cables; motor leads; and jacket repairs. This tape should be applied in successive half-lapped level wound layers until desired build-up is reached. It should be applied like any rubber tape; that is, the side of the tape wrapped inside the roll should be applied outside on the splice (tacky side up). This will help prevent the roll from getting progressively further away from the work area. To eliminate voids in critical areas, highly elongate 130C tape. Stretch tape in critical areas just short of the breaking point; doing so will not alter its physical or electrical properties.
- Duck Brand Self-Fusing Rubber Splicing Tape
Duck Brand Self-Fusing Rubber Splicing Tape is used to protect your electrical project from the elements. Instantly create watertight barriers around low voltage electrical splices or wire repairs with Duck® Brand Rubber Splicing Tape. How does this electrical tape create such a durable seal? Its design allows super conformability and stretch so it easily wraps around even the trickiest wires. Plus, its easy-tear and removable liner takes the frustration out of the job - no need for tools to cut it, just use your hands to tear the tape, even with the liner. The tape is designed for use in splicing and terminating wires and cables. The tape is self-fusing which means it is an adhesive-free tape that fuses only to itself (no sticky residue left on surfaces).
- JVCC MAG-01-W Writeable Magnetic Tape [No Adhesive]
JVCC MAG-01-W Writeable Magnetic Tape is comprised of a multipole one face flexible magnet (composite of strontium and/or barium ferrite particles oriented with a thermoplastic polymer matrix). These permanent magnets remain magnetized indefinitely if not subjected to a demagnetizing force. This tape is not returnable for this reason. The side with polarity would be attracted to ferromagnetic materials such as iron, nickel and cobalt. It would also be attracted to a magnet of the opposite polarity. The tape is NOT attracted to itself (it repels) since it would need a magnet of the opposite polarity to attract. The tapes marked as write-on/wipe-off have a non-porous, smooth, and shiny white vinyl surface. Writeable with a dry erase marker and just wipe off. Applications include whiteboard, warehouse labels, store/retail shelf labels, schedule/planning boards, and control charts. The tapes marked as writeable have a porous, writeable, screen-printable matte white vinyl surface. Writeable with a permanent marker, or with a water soluble marker (wipe off with a damp rag) for non-permanent applications. Note, wiping off will gray surface over time. Applications include: automobile signs, marketing displays/premiums, business cards, warehouse/barcode labels, and control charts.
- JVCC SRT-700 Silicone Rubber Tape
JVCC SRT-700 Silicone Rubber Tape is a self adhering, self bonding (an adhesive-free tape that fuses only to itself) red triangular silicone tape. It offers excellent electrical insulation properties, moisture, chemical and UV resistance. It's self bonding properties offer excellent conformability and adherence to irregular and nontraditional surfaces. JVCC SRT-700 silicone tape is made of a special unsupported silicone rubber compound which readily adheres to itself when wrapped under tension and forms a homogeneous mass within 24 hours. The adhesion can be accelerated with heat and pressure. When applying the tape make sure it overlaps itself (since it only adheres to its own backing) and stretch/pull the tape tightly around the object (the tape has a white guide line down the middle to help in overlapping it correctly). The tape creates an instant, permanent water-tight seal and can withstand temperatures from -65°F to +500°F. No adhesive (self bonding) insures no residue. The tape has a triangular thickness so it is thinner at the edges and thicker in the middle. Applications for JVCC SRT-700 include: watertight insulated over wrap of any electrical or wiring connection, indoors and out; automotive and general fluid hose repair (keep in vehicle for emergency repairs); replacement for heat shrinkable tubing; and replacement for electrical tape on marine applications.
- Duck Brand Carpet Seaming Indoor/Outdoor Fiberglass Tape
Duck Brand Carpet Seaming Tape is a single-sided fiberglass tape with an adhesive backing on one side. The fiberglass carrier on the tape is moisture and mildew resistant. Duck Carpet Seaming Tape can be used both indoors and outdoors. The tape helps to quickly join carpet pieces together without special tools or irons - the tape is self stick and there is no liner to remove. Recommended for permanent applications. Application Instructions Position carpet as desired, butting together edges to be seamed. Fold back edges and begin to unroll tape into the exposed seaming area non-adhesive side to the floor. Caution: the adhesive on the tape is extremely aggressive and may become permanent with initial contact to carpet backing. Be certain to center the tape correctly as you begin. Continue to unroll tape several feet at a time pressing seam edges back down into adhesive firmly for good adhesion.
- JVCC MAG-01 Magnetic Tape [With Adhesive / 1/32" thickness]
JVCC MAG-01 Magnetic Tape is a flexible magnet mounted on a thin polyester film which has been coated on one side with an aggressive rubber based pressure sensitive adhesive. Tape is supplied self-wound on a semi-bleached kraft paper liner. The magnet is comprised of a multipole one face flexible magnet (composite of strontium and/or barium ferrite particles oriented with a thermoplastic polymer matrix). These permanent magnets remain magnetized indefinitely if not subjected to a demagnetizing force. This tape is not returnable for this reason. Please note this magnet has a thickness of 30 mils as noted in the product specializations so is slightly under 1/32" in thickness. As such it would not be able to hold up heavier weight items like heavy-weight fabric (see the 1/16" thick JVCC MAG-02 for heavier weight items). Through our own testing we have found when the surface area of a 2-1/2" long x 1" wide strip weighs up to 0.5 pounds it is attracted enough to MAG-01 to be held up. One way we've found to increase the magnetic attraction is to cut some MAG-01 into two pieces and then peel off the release liner to expose the adhesive side and then adhere to the two substrates. Then bring both magnetic sides together which typically creates a stronger magnetic bond. As noted above JVCC MAG-01 is a single-faced multi-pole magnet so one side has a polarity and the other side is coated with an adhesive. The side with polarity would be attracted to ferromagnetic materials such as iron, nickel and cobalt. It would also be attracted to a magnet of the opposite polarity. The tape is NOT attracted to itself (it repels) since it would need a magnet of the opposite polarity to attract.
- JVCC MAG-02 Magnetic Tape [With Adhesive / 1/16" thickness]
JVCC MAG-02 Magnetic Tape is a flexible magnet mounted on a thin 4.5 mil polyester film which has been coated on one side with an aggressive acrylic based pressure sensitive adhesive. The indoor/outdoor adhesive the tape is coated with is for bonding applications where outstanding adhesion, high shear and good solvent and UV resistance are required. The tape is supplied self-wound on a semi-bleached kraft paper liner. The magnet is comprised of a multipole one face flexible magnet (composite of strontium and/or barium ferrite particles oriented with a thermoplastic polymer matrix). These permanent magnets remain magnetized indefinitely if not subjected to a demagnetizing force. This tape is not returnable for this reason. Please note this magnet has a thickness of 60 mils as noted in the product specializations so is slightly under 1/16" in thickness. Through our own testing we have found when the surface area of a 2-1/2" long x 1" wide strip weighs up to 0.7 pounds it is attracted enough to MAG-02 to be held up. As such it would hold up heavier weight items better than the 1/32" thick MAG-01 Magnetic Tape we also sell; however it is not magnetic enough to work through a substrate like leather. Also as noted above JVCC MAG-02 is a single-faced multi-pole magnet so one side has a polarity and the other side is coated with an adhesive. The side with polarity would be attracted to ferromagnetic materials such as iron, nickel and cobalt. It would also be attracted to a magnet of the opposite polarity. The tape is NOT attracted to itself (it repels) since it would need a magnet of the opposite polarity to attract.
- JVCC PolyPro Twisted Rope
JVCC PolyPro Twisted Rope is superior to manila rope and conventional polypropylene mono filament rope is several respects This rope is manufactured from extruded copolymer (polypropylene and polyethylene) fibers whose unique properties result in ropes that, size for size, are almost triple the strength of traditional high quality manila rope and twice the strength of conventional polypropylene rope. Not only is PolyPro rope far stronger, but it also weighs much less, making it easier to handle. It also has very good resistance to rot mildew, acids and alkalis. It does not harden with age, experience any loss of strength, either from wetness or from drying, and has among the lowest percent elongation. The abrasion resistance of the rope is superior to manila and polypropylene rope and (a particularly important consideration for rigging application) withstands shock load much better than manila rope as well. Unused PolyPro rope has a slightly stiff feeling as it comes off the coil, but it rapidly becomes highly pliable once it is placed in service. After running only a short time over sheaves, the rope will develop a surface "fuzz" which makes for a silky feel and excellent handling characteristics, unlike polypropylene rope which is coarse and slippery on handling.
- JVCC RW-32 Roller Wrap Tape [Dimpled Siliconized Cloth]
JVCC RW-32 Roller Wrap Tape is an embossed or dimpled siliconized cloth tape coated with an acrylic adhesive system. It is designed to protect web rollers from the buildup of adhesives, inks, coatings, and other materials in the adhesive tape manufacturing, general converting, printing, textiles and paper & film industries. It is sometimes referred to as the printer's friend. By reducing buildup on idler, feed, and take-up rollers, The specially formulated adhesive on the tape minimizes residue upon removal minimizing the amount of roller clean up required when the tape is changed which extends the life of the roller itself. JVCC RW-32 Web Roller Wrap Tape significantly reduces clean-up and maintenance times making production processes much more efficient. It's high co-efficient of friction provides an anti-slip surface and allows it to grip the web and keeps materials moving while preventing the build-up of inks, adhesives and coatings (anti-stick). Also has excellent continuous temperature resistance.
- Duck Brand Drywall Joint Self-Adhesive Fiberglass Tape
Duck Brand Drywall Joint Tape is a 100% fiberglass mesh tape. It is self-adhesive and repositionable. Also strong, fast and easy to use - no need to re-apply compound to joints. Used for repairing cracks and small holes. Instructions for Taping Drywall (Sheetrock) Joints Clean surface of dust and dirt. Position tape over seam and cut to exact length. When seaming drywall/wallboard joints, use only quick setting joint compound. For best results maintain room temperature between 50° - 70°F. Apply joint compound working it through the mesh. Let dry to manufacturer's instructions and sand smooth. Apply a second, thinner coat wider than the first feathering edges outward. Let dry and sand smooth. Instructions for Repairing Cracks Slightly open up crack to a width of 1/8" and fill with ready mix or any setting compound. Let dry to manufacturer's instructions. Clean and sand surface. Apply joint tape to the repair area; overlapping the end of each crack by 1" or more. Spread compound down the crack, working it through the mesh. let dry and sand smooth. For a finished appearance apply a second, thinner coat wider than the first. Let dry and sand smooth. Instructions for Patching Holes Clean and sand surface. Cut two pieces of joint tape 2" longer than the hole dimensions. Apply tape over the hole in a criss-cross manner so entire opening is covered by both layers. Depress joint tape 1/4" into hole and fill with ready mix or any setting compound. Let dry to manufacturer's instructions and sand smooth. For a finished appearance apply a second, thinner coat wider than the first. Let dry and sand smooth.
- JVCC TL-4 Tie Line
JVCC TL-4 Tie Line is also known as "trick" line or "sash cord". The #4 cotton tie line is coated which allows for more permanent use with greater holding power. Comes in reels of various sizes.
- Jaybird & Mais ICE Instant Ice Pack
Jaybird & Mais ICE Instant Ice Pack is a disposable ice compress in a sturdy two-ply poly bag which is convenient for travel. On average will stay cold for 20 minutes once activated. The ice packs should not be exposed to over 100°F temperatures for extended periods of time. Contains ammonium nitrate and water. Directions for use: Shake contents to the bottom of the bag. Locate the inner pouch and squeeze firmly to break. Shake gently to assure complete activation. Wrap in a soft cloth and apply (packs are double-bagged however as a safety precaution direct skin contact should be avoided in case bag gets punctured).
- Wooster Floor Prep Cleaning Solution
Wooster Floor Prep is an alkaline solvent compound used for heavy-duty cleaning. It is an easy to handle, fast cleaning liquid designed for steam or spray cleaning as well as floor scrubbing machines and can be used in both interior and exterior applications. It is designed to clean areas subjected to heavy grease, oil and carbonaceous soils, and can be used to clean any type of surface. Wooster Floor-Prep has been approved by the U.S.D.A. for cleaning floors and walls in poultry, meat, rabbit and egg processing plants. Biodegradable and phosphate-free. Floor Prep is a highly alkaline material. Direct contact may cause burns of eyes and skin. It is harmful if swallowed. Avoid contact with eyes, skin and clothing. Wear protective gloves, safety goggles and suitable protective clothing when handling. Wash thoroughly after handling. Do not take internally. Application Instructions Dilute 1/4 pint (4 fl. ounces) of Floor Prep to one gallon of warm-to-hot water (up to 160°F) - this amount of solution will clean approximately 30 to 40 square feet of area. Pour the cleaner over the area to be cleaned and allow to soak up to 15 minutes. After soaking, clean area with a power scrubber or agitate with a stiff bristled brush. Agitate until a foaming action occurs. Follow by two (2) thorough high-pressure water rinses, preferable hot.