JVCC DLM0300

JVCC DLM0300 Definite Length Tape Dispenser [Manual]

  • Quantity
    View Full Pricing Table
    View "Full Pricing Table" below for detailed pricing and additional sizes!
  • Color
    Black
  • Dispenser Size
    for tape up to 1" wide
  • Price
    $ Price/photo will update once color & size have been chosen.
Warning
Before ordering, please read the "Product Description & Specs" tab content for more information about this item.

DLM0300 Standard sizes

DISPENSER SIZEITEM # DISPENSERS PER CASE QUANTITY ORDERING PRICE PER DISPENSER PRICE PER CASE

for tape up to 1" wide

DLM03006

Single Dispenser (1-5 Dispensers)

1 Case (6-11 Dispensers)

2 Cases (12-17 Dispensers)

3+ Cases (>= 18 Dispensers)

$84.29

$76.61

$75.97

$75.33

N/A

$459.66

$455.82

$451.98

Product Description

JVCC DLM0300 Definite Length Tape Dispenser is a manual-feed definite-length pressure sensitive tape dispenser with a hand lever. It dispenses tape from widths of 1/4" to 1". It offers definite lengths from 1/2" to 4" with a single pull. Tape is cut by pulling upwards across a serrated blade. Moveable blade holder for easy tape loading. Heavy base for stability. Maximum roll outside diameter is 4-3/4" and holds tapes on a 3" diameter core. CM0300 is recommended for BOPP and some polyester film tapes to 3.5 mil thick. Also for crepe paper masking and some flatback paper tapes. It is not suitable for thick films, stretchy films (vinyls), or foil tapes. Helps to save on tape costs by always dispensing just the minimum length you need to get the job done. Great for retail establishments like deli and sub shops.

Usage Instructions

  1. Remove the core holder from the dispenser, load tape, and place the core holder back on the dispenser.
  2. Open the cover plate door on top of the dispenser and set the tapes leading edge on the rollers. Ensure that the leading edge of the tape is flat and close the cover plate door.
  3. Adjust the manual tape dispenser lever by setting the arm to the desired length. Accomplish this by loosening the knob on the lever and position the arm higher up to obtain a longer length. Tighten the knob to set at the dispensed length. There is no gauge on this dispenser. Need to set length via trial and error on arm height for the first time.
  4. Press down on the dispenser's lever to dispense the tape at a consistent length. Pull the dispensed tape in an upward motion to cut the tape.

 

Technical Information

JVCC DLM0300 Definite Length Tape Dispenser
  • Feed: Manual
Note: Specifications are those given by manufacturers and are not tested for accuracy.
JVCC DLM0300 Definite Length Tape Dispenser [Manual]
hot melt rubber (synthetic)
Offers the widest range of application flexibility available. Exhibits excellent processing performance whether manually or automatically applied. Has superior tensile strength, adhesion properties and holding force which ensures consistent, reliable seals. Hot melt adhesive will bond faster to a surface which is referred to as quick-grab or quick-stick. It typically has higher tack (will feel stickier to the touch), but is also softer. It has lower heat resistance, shear resistance, and sometimes UV resistance than an acrylic adhesive. NOTE: it is called hot melt because the adhesive is applied hot by the manufacturer and then hardens as it cools (you do not need to apply heat to the tape yourself).
natural rubber
Properties are similar to that of hot melt rubber, but natural rubber often holds where other adhesives won't (recycled fibers, dust, cold, heat and heavy loads). It provides good overall adhesion and moisture resistance.
acrylic
Offer excellent performance, especially for applications in temperatures less than 40°F and greater then 120°F. It provides excellent clarity, has high shear strength, is usually more permanent/durable even when exposed to moisture, and it ages well over extended periods in fluorescent and sunlight. Since it remains clear for the life of the application and does not yellow over time it is ideal for applications such as sealing white cartons. While it has good initial adhesion it does take 24-48 hours to cure and to achieve its maximum bond strength (has gradual adhesion buildup). Another difference between hot melt rubber and acrylic adhesive is if you fold tape over making the two adhesive sides touch the acrylic adhesive will remain attached to the carrier (e.g. paper, film) while a hot melt adhesive will stick to itself and pull off of the carrier. It is the best choice for clarity, UV resistance and aging characteristics.
silicone
Is great for extreme temperature applications since silicone adhesive can work in continuous operating temperatures from -100°F to 500°F. They also exhibit good chemical resistance, retain electrical properties, and remove cleanly with little or no residue.
zinc oxide
Zinc oxide based adhesive formula is a skin-friendly adhesive which is commonly used on sports medicine tapes.
Thickness, AKA caliper or gauge, refers to the distance from one surface of a tape backing, or adhesive, to the other.
1 mil = 1/1000 of an inch
Examples: 1/16 inch = 62.5 mils; 1/32 inch = 31.25 mils
Shopping Cart Summary
Continue Shopping View Shopping Cart
Search  

Newsletter Signup

Sign up today to be notified of upcoming deals and exclusive offers!

Adhesive Tape Blog
Video Resource Library
How-To Resource Articles
See also
Electrical Tapes
Tapes for Scrapbooking