JVCC SRT-700 Silicone Rubber Tape
JVCC SRT-700 has been discontinued and only limited inventory now remains.
SRT-700 Standard sizes
|ROLL SIZE||ITEM #
||ROLLS PER CASE
||PRICE PER ROLL
||PRICE PER CASE
1 in. x 30 ft. (triangular thickness)
Single Roll (1-35 Rolls)
1 - 2 Cases (36-107 Rolls)
3 - 4 Cases (108-179 Rolls)
5+ Cases (>= 180 Rolls)
Nominal Tape Widths vs Actual Widths
5% narrower than the NOMINAL width shown in inches. Examples:
Tape rolls are cut to standard tape industry metric widths of approx. 24mm per 1-inch of nominal width ordered. As a result ACTUAL tape widths are normally
- 1" Nominal width = 15/16" (24mm) Actual width
- 2" Nominal width = 1-7/8" (48mm) Actual width
- 3" Nominal width = 2-13/16" (72mm) Actual width
Note that tape rolls are NOT guaranteed to be splice-free.
JVCC SRT-700 Silicone Rubber Tape is a self adhering, self bonding (an adhesive-free tape that fuses only to itself) red triangular silicone tape. It offers excellent electrical insulation properties, moisture, chemical and UV resistance. It's self bonding properties offer excellent conformability and adherence to irregular and nontraditional surfaces. JVCC SRT-700 silicone tape is made of a special unsupported silicone rubber compound which readily adheres to itself when wrapped under tension and forms a homogeneous mass within 24 hours. The adhesion can be accelerated with heat and pressure. When applying the tape make sure it overlaps itself (since it only adheres to its own backing) and stretch/pull the tape tightly around the object (the tape has a white guide line down the middle to help in overlapping it correctly). The tape creates an instant, permanent water-tight seal and can withstand temperatures from -65°F to +500°F. No adhesive (self bonding) insures no residue. The tape has a triangular thickness so it is thinner at the edges and thicker in the middle. Applications for JVCC SRT-700 include: watertight insulated over wrap of any electrical or wiring connection, indoors and out; automotive and general fluid hose repair (keep in vehicle for emergency repairs); replacement for heat shrinkable tubing; and replacement for electrical tape on marine applications.
JVCC SRT-700 Silicone Rubber Tape
- Adhesive: silicone How are adhesives different?
- Carrier/Backing: self-fusing rubber
- Release Liner: cellophane film
- Tensile Strength: 700 pounds per inch (longitudinal)
- Service/Operating Temperature: -65°F to 500°F
- Elongation: 300%
- Thickness: 10 mils at edges to 30 mils in center
- Core: 1-1/2" diameter
Note: Specifications are those given by manufacturers and are not tested for accuracy.
Please note that tape rolls are NOT guaranteed to be splice-free. Tape rolls are typically cut to standard tape industry metric-cut sizes - or approx 5% narrower than the nominal size (i.e. 24mm per 1-inch of nominal width ordered).
Please contact us to inquire about pricing for full-cut widths (e.g. a 6 inch roll cut to exactly 152mm instead of 144mm).
PLEASE NOTE: "Alternative" to is NOT the same as equivalent to so please ensure the specifications listed are suitable for your application.
This product can be used as an alternative to the following products(s):
hot melt rubber (synthetic)
Offers the widest range of application flexibility available. Exhibits excellent processing performance whether manually or automatically applied. Has superior tensile strength, adhesion properties and holding force which ensures consistent, reliable seals. Hot melt adhesive will bond faster to a surface which is referred to as quick-grab or quick-stick. It typically has higher tack (will feel stickier to the touch), but is also softer. It has lower heat resistance, shear resistance, and sometimes UV resistance than an acrylic adhesive. NOTE: it is called hot melt because the adhesive is applied hot by the manufacturer and then hardens as it cools (you do not need to apply heat to the tape yourself).
Properties are similar to that of hot melt rubber, but natural rubber often holds where other adhesives won't (recycled fibers, dust, cold, heat and heavy loads). It provides good overall adhesion and moisture resistance.
Offer excellent performance, especially for applications in temperatures less than 40°F and greater then 120°F. It provides excellent clarity, has high shear strength, is usually more permanent/durable even when exposed to moisture, and it ages well over extended periods in fluorescent and sunlight. Since it remains clear for the life of the application and does not yellow over time it is ideal for applications such as sealing white cartons. While it has good initial adhesion it does take 24-48 hours to cure and to achieve its maximum bond strength (has gradual adhesion buildup). Another difference between hot melt rubber and acrylic adhesive is if you fold tape over making the two adhesive sides touch the acrylic adhesive will remain attached to the carrier (e.g. paper, film) while a hot melt adhesive will stick to itself and pull off of the carrier. It is the best choice for clarity, UV resistance and aging characteristics.
Is great for extreme temperature applications since silicone adhesive can work in continuous operating temperatures from -100°F to 500°F. They also exhibit good chemical resistance, retain electrical properties, and remove cleanly with little or no residue.
Zinc oxide based adhesive formula is a skin-friendly adhesive which is commonly used on sports medicine tapes.
Thickness, AKA caliper or gauge, refers to the distance from one surface of a tape backing, or adhesive, to the other.
1 mil = 1/1000 of an inch
Examples: 1/16 inch = 62.5 mils; 1/32 inch = 31.25 mils