NOTE: Federal regulations prohibit the shipment of restricted products (aerosol cans, flammable liquids, etc.) by air so please only choose UPS Ground or Surepost as your shipping method if including this product in your order. We can not export this product outside the continental U.S. for this reason.
Heskins PRIM Porous Surface Primer
Before ordering, please read the "Product Description & Specs" tab content for more information about this item.
Heskins Porous Surface Primer is a water-based primer which helps to create a stable surface for your tape application. Heskins recommends that the surface is sealed prior to the application of the primer. A non-sealed surface may allow moisture to travel through to the tape and this could allow the tape to lift or not fully adhere to your substrate. Heskins Primer will help to prevent the moisture from affecting the adhesive of tread and other floor marking tapes.
Simply brush down (paint) only onto the area where you will be applying the adhesive tape and allow the product to dry. The drying time is typically 10-30 minutes depending upon the application temperature and surface type. The 33.8 fluid ounce container of Surface Primer covers approximately 50 square feet of non-slip stair tread area.
* Multiple cases may be shipped per package in order to minimize the charge for shipping.
Heskins PRIM Porous Surface Primer
Note: Specifications are those given by manufacturers and are not tested for accuracy.
PRIM Standard sizes
|BOTTLE SIZE||ITEM #
||BOTTLES PER CASE
||PRICE PER BOTTLE
||PRICE PER CASE
33.8 fluid ounces
UPC = 692764160658
Single Bottle (1-3 Bottles)
1 - 2 Cases (4-11 Bottles)
3 - 4 Cases (12-19 Bottles)
5+ Cases (>= 20 Bottles)
a 13% discount
a 14% discount
a 15% discount
Question & Answers
hot melt rubber (synthetic)
Offers the widest range of application flexibility available. Exhibits excellent processing performance whether manually or automatically applied. Has superior tensile strength, adhesion properties and holding force which ensures consistent, reliable seals. Hot melt adhesive will bond faster to a surface which is referred to as quick-grab or quick-stick. It typically has higher tack (will feel stickier to the touch), but is also softer. It has lower heat resistance, shear resistance, and sometimes UV resistance than an acrylic adhesive. NOTE: it is called hot melt because the adhesive is applied hot by the manufacturer and then hardens as it cools (you do not need to apply heat to the tape yourself).
Properties are similar to that of hot melt rubber, but natural rubber often holds where other adhesives won't (recycled fibers, dust, cold, heat and heavy loads). It provides good overall adhesion and moisture resistance.
Offer excellent performance, especially for applications in temperatures less than 40°F and greater then 120°F. It provides excellent clarity, has high shear strength, is usually more permanent/durable even when exposed to moisture, and it ages well over extended periods in fluorescent and sunlight. Since it remains clear for the life of the application and does not yellow over time it is ideal for applications such as sealing white cartons. While it has good initial adhesion it does take 24-48 hours to cure and to achieve its maximum bond strength (has gradual adhesion buildup). Another difference between hot melt rubber and acrylic adhesive is if you fold tape over making the two adhesive sides touch the acrylic adhesive will remain attached to the carrier (e.g. paper, film) while a hot melt adhesive will stick to itself and pull off of the carrier. It is the best choice for clarity, UV resistance and aging characteristics.
Is great for extreme temperature applications since silicone adhesive can work in continuous operating temperatures from -100°F to 500°F. They also exhibit good chemical resistance, retain electrical properties, and remove cleanly with little or no residue.
Zinc oxide based adhesive formula is a skin-friendly adhesive which is commonly used on sports medicine tapes.
Thickness, AKA caliper or gauge, refers to the distance from one surface of a tape backing, or adhesive, to the other.
1 mil = 1/1000 of an inch
Examples: 1/16 inch = 62.5 mils; 1/32 inch = 31.25 mils